Lashe® Fume Free adhesive is medical-grade, has been developed and formulated
by The Lashe® and produced in an FDA-certified facility in the USA. It is
the same quality of adhesive used for suture-less wound closure. The most
safe and high-performance adhesive on the market. Easy to work with and
provides a medium strength bond.
Fume Free adhesive was developed for those clients with extreme allergies,
severe seasonal allergies and those on medications, including hormonal
medications such as thyroid medications. It is sold in the quantity of 1
gram on account that you may only have a few clients needing the Fume Free adhesive,
as opposed to the vast majority (over 95%) of your clients that will be using
the Rapid Dry. It is easily workable and not thick or clumpy.
Features of The Lashe® Fume-Free adhesive include:
- Medical grade – most sterile adhesive on the
- Produced in an FDA-certified facility in the
- Most sensitive adhesive – least irritating
you can find
- Sets instantly – produces medium strength
- Ideal viscosity – not to thick, not watery
- Easy to work with – cuts down on appointment
- Formulated not to bond with itself – no need
- Least to no fumes – tolerated by client and
- Stays soft and flexible – does not
crystallize, not brittle
- True black color with luster and sheen –
- Easy-to-use, see-through bottle – does not
- Shelf life 2 months – opened or unopened
results follow the detailed directions below:
Fume Free Adhesive Instructions
Step 1: Shake adhesive well. To open,
hold the bottle at the neck and unscrew the cap. Do not squeeze the body of the
bottle as it will force adhesive through the nozzle. One hand must be on the
neck and the other on the cap.
Step 2: Attach a dosing tip by
placing it on the nozzle of the bottle firmly and leave it on for the duration.
Step 3: If lashes are clean and free
of makeup, saturate them with saline using two oval and pointed cotton swabs.
If lashes are not clean, cleanse with an oil free cleanser, like The Lashe®
Cleansers, and then you must rinse with saline twice. Use two
sets of cotton swabs to do this in order to thoroughly rinse cleanser and then
dehydrate the natural eyelashes. Avoiding this step is like putting makeup on a
Step 4: Dispense a small drop of
adhesive on a flat, non-porous surface, like our 2” round Adhesive Shield. You
will need to re-drop a small drop every 15 to 20 minutes or so, depending on
your speed and room dynamics.
Step 5: Coat only the base of the
extension up to 1/4 of its overall length (half of the half). Enter at the
bottom of the adhesive drop, then down and out to exit. At this point you
should have a bead of adhesive at the end of the extension no larger than twice
the thickness of the extension at the base, i.e. with a 0.15mm extension you
should have a bead no larger than 0.30mm.
Step 6: Place the extension on the
natural lash 2mm away from the lash line (about the thickness of a nickel).
Move the extension to 1mm from the lash line (a little less than the thickness
of a dime), orientate and release. Make sure there is a seamless connection
between the extension and natural lash with no air pockets.
adhesive in a cool, dry place; not on a cold surface. Do Not Refrigerate.
recommend the use of our Micro Dosing tips; they help control the size of the
drop and keep the air out of the bottle. They prevent accidents and
over-pouring, thus controlling adhesive usage.
method for coating the extensions is to be entering the adhesive drop at the
same point and close to the flat surface. This will keep the outer layer
intact. Breaking the surface tension will cause the adhesive to dry out faster.
Exit the drop by pushing down and out to create a smooth coating and to pick up
a bead at the end of the extension. So long as there is a seamless connection,
the extensions will stay on for the full life cycle of the lashes and shed
together with the natural lashes. If you see popping off at the back, this is a
technique issue or the client is using oil based products at home.
formulation is concentrated and very little adhesive is necessary to create a
seamless bond. The adhesive will allow you to work quicker once you get the
rhythm of it. Do not over work the adhesive as it will dry in the air and not
bond properly. Do not “paint” the adhesive on the lashes. You should not see
any clumps or have to separate lashes at the end of the appointment. The
adhesive is formulated not to cross bond with itself or cause static
Conditioner is a fabulous aftercare product, but we also use it as a prep
product prior to the extension application in order to un-tangle unruly or wiry
lashes. In that case, and after you have cleansed the lashes, take two
micro-brushes and acquire a small amount of conditioner from the conditioner
applicator. Apply to the natural and extension lashes, if any. Rinse with
saline. The conditioner has a built in detangler that will separate the lashes.
It will also bring extended lashes back to life.
tip self-seals, snip the tip of the dosing tip to dispense. The dosing tip need
not be removed during the day as the adhesive creates a meniscus after adhesive
is dispensed, creating an airtight seal. We recommend that you place the bottle
cap atop the dosing tip for added protection.
Keep Out of Reach of Children
Immediately flush eyes with water for at least ten minutes. If eyes shut, do
not force open. Contact a Physician.
INHALATION: Immediately go to fresh air. If
problems persist, contact a physician.
Not to be
used if adhesive, latex or formaldehyde allergy exists. Attach up to 10 lashes
per eye and return in 48 hours for examination. Adhesive does not contain
are sensitive to extreme temperatures. See our Shipping & Returns policy
MSDS for more information.
Net wt. 1 gm. Made in USA.